Usbasp V2 0 Driver Windows 10 Pro

USB drivers available for Windows (using libusb, no drivers needed for Mac OS X or Linux. Durable off-the-shelf enclosure High speed! Max clock rate is 400KHz. Write speed:1Kb/s, read speed: 2Kb/s. (Atmega8 takes 8s to write, 4s to read/verify) 2 LEDs to indicate 'USB/Power good' and 'Busy'. Go to and download the software (note that Windows XP has a separate link). Plug in your USBasp or USBtiny device. In case your microcontroller uses a USBasp or USBtiny bootloader, enter bootloading mode, and let Windows detect the device (it will report driver not found).

Cheap USBASP programmer which you china buy on ebay, ali and others. Official project WebPage: http://www.fischl.de/usbasp/

Usbasp V2 0 Driver Windows 10 64-bit

JP1 – Supply Target – Choose between 5V and 3.3V.
JP2 – Self Program – jumper on for self program, normally free
JP3 – Slow SCK – Jumper on only if the target clock is lower than 1.5 MHz.
LED R – Programmer communicating with target device
LED G – Power on
IDC pinout:

I will write how to solve:

avrdude: warning: cannot set sck period. please check for usbasp firmware update

You have to flash a new firmware version: usbasp.2011-05-28. Precompiled bin to flash is in binfirmware directory.

I’ve got USBASP with Atmega8 so I will use usbasp.atmega8.2011-05-28.hex and Arduino UNO R3 as ISP to flash it.

First open ArduinoISP example in Arduino IDE 1.6.8 and upload the sketch (CTRL+U). Disconnect Arduino.
Connect arduino to usb asp directly (without any adapter only cables) as follows:
ArduinoUSBASP
105 (RESET)
111 (MOSI)
129 (MISO)
137 (SCK)
5V2 (VCC +5V)
GND10 (GROUND)
Set jumper on JP2 (you can solder goldpins).
Set power jumper for 5V (JP1)
Connect only Arduino to USB and check which port com it use. You must not connect usbasp to usb!
Download AVRDUDE avrdude-6.3-mingw32.zip: http://download.savannah.gnu.org/releases/avrdude/
Copy correct hex file to avrdude.exe file directory.
Check the connection with command:
avrdude: Version 6.3, compiled on Feb 17 2016 at 09:25:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is “C:WinAVR-20100110binavrdude.conf”
Using Port : COM4
Using Programmer : avrisp
Overriding Baud Rate : 19200
AVR Part : ATmega8
Chip Erase delay : 10000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
———– —- —– —– —- —— —— —- —— —– —– ———
eeprom 4 20 128 0 no 512 4 0 9000 9000 0xff 0xff
flash 33 10 64 0 yes 8192 64 128 4500 4500 0xff 0x00
lfuse 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
lock 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
calibration 0 0 0 0 no 4 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : STK500
Description : Atmel AVR ISP
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.04s
avrdude: Device signature = 0x1e9307 (probably m8)
avrdude: safemode: hfuse reads as D9
avrdude: safemode: hfuse reads as D9
avrdude: safemode: Fuses OK (E:FF, H:D9, L:9F)
avrdude done. Thank you.
replace COMX with correct com port for arduino.
Set the fuses like on Readme file:
# TARGET=atmega8 HFUSE=0xc9 LFUSE=0xef
# TARGET=atmega48 HFUSE=0xdd LFUSE=0xff
# TARGET=atmega88 HFUSE=0xdd LFUSE=0xff
with command:
If it recognize the M8 you can flash it:
avrdude: Version 6.3, compiled on Feb 17 2016 at 09:25:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is “C:WinAVR-20100110binavrdude.conf”
Using Port : COM4
Using Programmer : avrisp
Overriding Baud Rate : 19200
AVR Part : ATmega8
Chip Erase delay : 10000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Songs about turning 24. Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
———– —- —– —– —- —— —— —- —— —– —– ———
eeprom 4 20 128 0 no 512 4 0 9000 9000 0xff 0xff
flash 33 10 64 0 yes 8192 64 128 4500 4500 0xff 0x00
lfuse 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
lock 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
calibration 0 0 0 0 no 4 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : STK500
Description : Atmel AVR ISP
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.04s
avrdude: Device signature = 0x1e9307 (probably m8)
avrdude: safemode: hfuse reads as D9
avrdude: NOTE: “flash” memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file “usbasp.atmega8.2011-05-28.hex”
avrdude: input file usbasp.atmega8.2011-05-28.hex auto detected as Intel Hex
avrdude: writing flash (4700 bytes):
Writing | ################################################## | 100% 7.34s
avrdude: 4700 bytes of flash written
avrdude: verifying flash memory against usbasp.atmega8.2011-05-28.hex:
avrdude: load data flash data from input file usbasp.atmega8.2011-05-28.hex:
avrdude: input file usbasp.atmega8.2011-05-28.hex auto detected as Intel Hex
avrdude: input file usbasp.atmega8.2011-05-28.hex contains 4700 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 3.89s
avrdude: verifying …
avrdude: 4700 bytes of flash verified
avrdude: safemode: hfuse reads as D9
avrdude: safemode: Fuses OK (E:FF, H:D9, L:9F)
avrdude done. Thank you.
Done. Disconnect Arduino.

Driver Usbasp Windows 10

USBASP Drivers on Windows 8, 8.1 and Windows 10

Read this: http://tosiek.pl/manual-install-drivers-and-disable-drivers-signing-policy-on-windows-10-8-8-1/
You have to first disable check signed drivers on windows 8, 8.1 and 10!
(pull Shift and click to restart > Troubleshoot > Advanced options > Startup Settings > Restart button again > On the Startup Settings screen press 7 or F7 to disable driver signature enforcement.)
Download: usbasp-windriver.2011-05-28

Then install it manually in device manager.